If you have a gun with Cerakote, then you know how durable and long-lasting the cerakote finish can be.
In that case, you should know How To Clean A Cerakote Gun?
But even the best finishes need proper care and maintenance to keep them looking good and performing well.
Cerakote gun refinishing has taken the firearms world by storm, and it’s easy to see why.
These weapons look incredible, and they are also very resistant to wear and tear.
If you have a Cerakote gun, whether it’s your own or you work in the firearms industry, keeping it clean can be tricky and time-consuming.
Cerakote is a ceramic-based finish that can be applied to metals, plastics, polymers, and wood.
It is usually used on firearms as it increases durability and wears resistance.
Cerakote gun cleaning is the process of removing contaminants from the surface of the gun without damaging the finish.
- General Information About Cerakote
- How To Clean A Cerakote Gun?
- Deep Cleaning Instructions
- How Often Should I Cerakote My Gun?
- Benefits Of Cerakote Gun Cleaning
- How To Clean A Cerakote Barbell?
General Information About Cerakote
The ceramic-based finish Cerakote can be applied to wood, plastics, and polymers.
The unique thing about Cerakote is that it provides a durable protective coating that is also extremely thin.
This makes it ideal for use on firearms where you want to maintain the original look and feel of the gun while protecting it from wear and tear.
The best way to clean your cerakote gun is with a product specifically designed for cleaning cerakote guns.
These products are typically solvent-based and will quickly remove any dirt or debris from the surface of your gun.
Once you have used a cleaner specifically designed for cerakote guns, you can then use a regular gun cleaning solution to remove any residue.
It is important to note that you should never use abrasive cleaners or solvents on your cerakote gun.
These products can damage the finish and cause it to lose its protective properties.
If you are unsure about what product to use, always consult with a qualified gunsmith or firearms dealer.
How To Clean A Cerakote Gun?
Cerakote guns require very little maintenance and can be cleaned easily with the right products.
Cerakote is a tough and durable coating that is often used on firearms to protect them from the elements.
Despite this, this coating can also make it difficult to clean your gun properly.
Here are some tips on how to clean a Cerakoted gun:
- Use a toothbrush or other soft brush to remove any debris or dirt from the surface of the gun. Be sure to avoid scrubbing too hard, as this can damage the finish.
- Use a quality cleaning solvent designed for use with Cerakoted guns. Apply the solvent to a clean cloth and wipe down the entire surface of the gun.
- Use a lint-free cloth to remove any residual solvent from the gun. Be sure to wipe in the direction of the grain to avoid damaging the finish.
- Apply a quality gun oil or lubricant to the surface of the gun. This will help protect the finish and keep your gun working properly.
By following these simple steps, you can ensure that your Cerakoted gun is properly cleaned and protected.
For more information on how to care for your firearm, be sure to consult with a qualified gunsmith or firearms instructor.
Deep Cleaning Instructions
There are several methods of cerakote gun cleaning, but the best way to clean a gun with cerakote is by using a mild detergent and warm water.
The first thing you need to do is make sure that you have the proper supplies.
You will need a soft cloth, some rubbing alcohol, and a toothbrush.
Make sure that the cloth you use is soft so that it does not scratch the finish on your gun.
Once you have gathered all of your supplies, you are ready to start cleaning.
Begin by removing any dirt or debris from the surface of your gun with a soft cloth.
Be sure to avoid using too much pressure, as this can damage the finish.
Once you have removed all of the visible dirt, it is time to move on to the next step.
A further step, use rubbing alcohol and a toothbrush to scrub any stubborn dirt or grime from the surface of your gun.
Be sure to avoid using too much pressure, as this can damage the finish.
Once you have removed all of the stubborn dirt, rinse your gun off with warm water.
Then, apply a quality gun oil or lubricant to the surface of your gun.
This will help protect the finish and keep your gun working properly.
By following these simple steps, you can ensure that your gun is properly cleaned and protected.
Also keep In Mind When Cleaning Cerakote Gun
Avoid using solvents or harsh chemicals as they can damage the finish.
For best results, rinse the gun thoroughly with clean water after cleaning.
If you need to remove stubborn dirt or grime, you can use a soft brush such as a toothbrush.
Gently scrub the affected area and rinse with clean water.
Do not use abrasive materials such as steel wool or sandpaper as they will scratch the surface of the gun.
Cerakote gun cleaning is simple and easy to do, but it is important to be gentle and avoid damaging the finish.
With proper care, your cerakote-finished gun will last for many years.
How Often Should I Cerakote My Gun?
It is generally recommended to recoat your firearm every 12 to 24 months depending on how often it is used.
If you live in a humid climate or use your gun frequently, you may need to recoat more often.
You can tell when your gun needs to be cleaned when the color starts to fade or if there is any wear on the surface.
Cerakote gun cleaning is a simple and easy process that will help keep your gun in good condition for many years.
Don’t forget to follow the manufacturer’s instructions carefully and always use gentle, non-abrasive cleaners to avoid damaging the finish.
With proper care, your cerakote-finished gun will provide years of trouble-free service.
Benefits Of Cerakote Gun Cleaning
A cerakote finish is a kind of durable gun coating.
In order to determine whether a cerakote finish will last a long time, we need to consider two factors:
- Abrasion resistance.
- Rust resistance.
Abrasion occurs when a substance is scraped or worn away. And when it comes to barbells, any metal-on-metal contact might result in abrasion.
It appears to be in the top half in terms of abrasion resistance.
Nevertheless, do not use this as an excuse to let metal-on-metal contact with your bar.
In terms of rust resistance, nevertheless, Cerakote truly excels.
In a test conducted by NIC Industries, the parent firm that literally invented Cerakote, the Cerakote coating outperformed eight other coatings.
Almost all coatings corroded within 48 hours of being placed in a salt room, with the test concluding when Cerakote exhibited the first signs of corrosion at 2,034 hours.
Apparently, the Cerakote coating is not rust-resistant.
Moreover, it is FAR superior to other coatings and appears to annihilate them in a direct comparison.
And despite the fact that this coating was initially designed to protect firearms from rust and abrasion, we believe this test is still a good predictor of its capacity to preserve a barbell.
How To Clean A Cerakote Barbell?
To clean a cerakote barbell, you’ll need a few things.
Here are all of them:
- Old rag
- Disposable gloves
- Nylon bristle brush (make sure you don’t use a metal brush!)
- Microfiber towel
- 3-in-1 oil
The following is a complete list of the steps required to clean a cerakote barbell:
- Take the barbell off
- Prop it up
- Scratch the bar’s shaft
- Add additives
- Employing oil
- Wipe off the bar
Take The Barbell Off
Take your barbell out of your rack first.
After cleaning off your bar, you won’t want the sweat, dead skin, or oil drippings all over it.
An old towel or long piece of cardboard would be ideal to lay on top of it.
It may also be possible to take it outside to clean it if the weather permits.
Prop It Up
It will be necessary to raise your cerakote barbell off the floor or ground in order to achieve clearance.
To enable you to prop up the bar, you may either make use of some 4×4 pieces of wood or simply attach a spring collar to each of the sleeves.
Then put on your work gloves, because it’s time to get down to business.
Scratch The Bar’s Shaft
Use the brush with the nylon bristle to give the shaft of the barbell a good cleaning.
This will assist in releasing any debris that has become lodged within the knurling over the course of time.
Add The Additives
After that, smear the 3-in-1 oil in a zigzag pattern along the whole length of the barbell’s shaft.
You can choose to use a thinner layer of coating for a quick touch-up, or you can apply a thicker layer if you have some badly corroded sections. Both options are acceptable.
Employing The Oil
Now, take your brush with the nylon bristle again, and using firm pressure, push the oil into the surface of the brush by scrubbing back and forth.
Rust and any other muck that has become embedded in the knurling can be more easily removed with the assistance of the lubricant (and the scrubbing motion), respectively.
Be aware that it is simpler to work in 12″ chunks at a time, in order to make certain that each section has the same level of care.
Wipe Off The Bar
Last but not least, get an old rag from your drawer, run it along the shaft of the barbell, and wring it out to remove all of the oil, chalk, and filth that you’ve dislodged with the brush.
The last wipe with a clean microfiber towel will take up any debris or fuzzies that may have been overlooked throughout the cleaning process.
It is important to clean your firearms after every use so they remain in top condition. In this manner, the action will be able to function safely and properly and the ammunition will be able to work as it should. The work should be done on a cleared table or bench. Cleaning should always be your top priority.
Frequently Asked Questions
Is brake cleaner spray safe?
It is common for spray brake cleaners to contain highly toxic chemicals and probable carcinogens, such as dichloromethane (also known as methylene chloride (DCM) and tetrachloroethylene (also known as perchloroethylene or perchloroethylene).
Should you oil a Cerakote gun?
Stainless steel surfaces are safe to clean with Cerakote cleaners. It usually takes 200 to 300 rounds to break in a firearm with quality gun oil or grease if it has been completely refinished in Cerakote or Duracoat. The weapon can be lightly lubricated after this period has passed!
Can you clean a suppressor with brake cleaner?
A brass brush, brake cleaner, soapy water, and dental picks will make your gear and yourself safer. The best way to get things started is to soak your flash suppressors or cans overnight in penetrating oil.
Does Cerakote finish make a good gun finish?
Ceramic composites produce a solid finish that is able to withstand impacts, scratches, and dings if dropped. The Cerakote finish is an excellent option to have your gunsmith apply to aftermarket firearms to add both a nice new look and durability to the firearm.
What kind of air compressor do I need for Cerakote?
Cerakote stations require compressed air, so you don’t need a large air compressor, but a 20-gallon compressor built with a maximum PSI of 150 will allow you to hold down the spray nozzle for quite some time.
What is cerakote discussion starter kit?
These discussion starter kits are designed for a beginner wanting to try Cerakote, and they come with essential tools and a coating.
Are organic solvents good for guns?
Most experts agree that using organic solvents to clean firearms can be helpful in removing built-up dirt and grease, and it can also help prevent corrosion. That said, it’s important to use caution when using any type of solvent, as it’s possible to damage the firearm if too much is used. It’s always best to consult with a professional gunsmith if you have any questions or concerns about cleaning your firearm.
Can you Cerakote old thread?
Yes, it is possible to Cerakote old threads. This can be done by first sanding down the threads to bare metal and then applying a thin layer of Cerakote. It is important to ensure that the Cerakote is evenly applied and that there are no gaps or voids in the coating, as this could result in problems with the threads binding or seizing up.
Can you Cerakote a new thread?
yes, you can Cerakote new thread. There are a few things you need to keep in mind, however. First, make sure that the surface is clean and free of any oils or contaminants. Second, roughen the surface of the substrate slightly to help promote adhesion. Third, apply the Cerakote evenly and carefully to avoid runs or sagging. Once dry, it will be very difficult to correct any imperfections, so take your time and do it right!
Can you Cerakote threads?
It’s not just that Cerakote is the best paint for corrosion protection, it’s also that it can be applied to all parts without expensive masking, including any difficult threads, valves, and impellers.
What is cerakote forum community dedicated to?
The Cerakote Forum Community is dedicated to providing a place for like-minded individuals to share information and ideas related to the popular firearm coating process known as Cerakote. This community website is a great resource for anyone looking to learn more about how to apply Cerakote, or for those who simply want to explore the world of firearm customization.
Does Cerakote scratch easily?
As a ceramic polymer-based formulation with industry-leading durability, hardness, scratch resistance, corrosion resistance, flexibility, heat, and chemical resistance, Cerakote® combines ceramic polymer with a proprietary formula that is highly versatile.
Why is my Cerakote rough?
Poor solvent transfer during application is typically the cause of dry spray’s sandpaper-like appearance. When the cerakote is fully cured, it should always have a smooth and slick finish. Wetting out the coating is very important during the application phase to prevent dry sprays.
What is cerakote new second media corp?
Cerakote New Second Media Corp is a new media company that focuses on creating and distributing digital content. Its mission is to provide users with an unforgettable experience by delivering quality content that is both informative and entertaining.
Why is my Cerakote rough?
A dry spray is usually caused by poor solvent transfer during the application, resulting in a rough, sandpaper-like appearance. After the product has been fully cured, the finish should be smooth and slick. Weting out the coating is very important during the application process to avoid dry sprays.
Can you touch up Cerakote?
A 1mL bottle of Cerakote (some colors are not air cure) to touch up any marks or scratches on your parts. We try to use the High Temp C series of Cerakote for our touch-up kits. Most touch-up kits use the Cerakote High Temp C series.
Can you air dry Cerakote?
Let it air dry. After approximately 35 minutes, the parts will be tack-free. It is important not to bump or touch the parts at this point since the coating is still wet. A partial cure will occur after 24 hours, and a full cure will occur after five days.